Title: Inverted Bictory
Description: new mod
Description: new mod
el3ctricAmp - May 6, 2006 11:33 AM (GMT)
Inverted Bictory Fusion Mod tutorial
ok first off this mod takes a lot of stuff to make, but ends up as a really good mod with a COP thats directly in the center.
the materials:
6 bic roundstic caps (two of the caps should be transparent)
1 bic roundstic barrel
1 pilot g2 grip
1 rsvp grip
1 bic velocity grip
1 piece from a pencil about 4cm or 5cm
Directions:
1. cut the bic roundstic barrel into 2 halves
2. get the 2 transparent caps and cut about 2cm from the closed end of the cap
3: put each of the transparent caps on each of the roundstic barrels and put the piece of the pencil inside of the part you cut of the cap so it connects both the caps together plus the barrels on each end.
4: then get 2 other bic caps and cut all of it only leaving the end part of the cap with the clip part on it
5: get the remaining 2 bic caps
6: cut velocity grips in half
7: cut pilot g2 grip into 4 thin parts
8: cut the rsvp grip in half and in half again. Only use 2 of the pieces of rsvp grip
9: so now get the whole bic caps and put the rsvp and velocity grips on it and close it off with the small clip part bic cap on each.
Put the thin pilot g2 grips on the small clip part bic cap on each...
and your finally done! :D
Spin it away! :pp :pp
EDIT:
O yea and if u get stuck in what it looks like check out my pic
ok first off this mod takes a lot of stuff to make, but ends up as a really good mod with a COP thats directly in the center.
the materials:
6 bic roundstic caps (two of the caps should be transparent)
1 bic roundstic barrel
1 pilot g2 grip
1 rsvp grip
1 bic velocity grip
1 piece from a pencil about 4cm or 5cm
Directions:
1. cut the bic roundstic barrel into 2 halves
2. get the 2 transparent caps and cut about 2cm from the closed end of the cap
3: put each of the transparent caps on each of the roundstic barrels and put the piece of the pencil inside of the part you cut of the cap so it connects both the caps together plus the barrels on each end.
4: then get 2 other bic caps and cut all of it only leaving the end part of the cap with the clip part on it
5: get the remaining 2 bic caps
6: cut velocity grips in half
7: cut pilot g2 grip into 4 thin parts
8: cut the rsvp grip in half and in half again. Only use 2 of the pieces of rsvp grip
9: so now get the whole bic caps and put the rsvp and velocity grips on it and close it off with the small clip part bic cap on each.
Put the thin pilot g2 grips on the small clip part bic cap on each...
and your finally done! :D
Spin it away! :pp :pp
EDIT:
O yea and if u get stuck in what it looks like check out my pic
slickhare - May 7, 2006 12:43 AM (GMT)
looks ok. but it uses so much material to make!
Toast - May 7, 2006 12:58 AM (GMT)
im with slickhare.
i dont the think more weight is enough reasoning to blow all your materials on an alternative BIC.
but whatever, looks cool with the caps in the middle and all :D
i dont the think more weight is enough reasoning to blow all your materials on an alternative BIC.
but whatever, looks cool with the caps in the middle and all :D
el3ctricAmp - May 7, 2006 01:31 AM (GMT)
if u just try the mod, it will be worth while
everun - May 7, 2006 02:09 AM (GMT)
When I get some more roundstics I will try it!
Mrvile - May 7, 2006 05:34 AM (GMT)
Well, it's creative, but it has some flaws. Those things sticking out in the middle (the leftover pieces of the caps) are very intrusive, but I think they can be easily sanded off. Also, this mod requires like 11 pens, some which are cheap, but some which are very expensive (like the G2) and overall the mod is quite wasteful.
cudofcow - April 21, 2008 07:39 PM (GMT)
what a piece of crap....lol
cudofcow - April 21, 2008 07:39 PM (GMT)
what a piece of crap....lol :spin: